+ Post New Thread
Threads 1 to 7 of 7

Forum: MSCTI

The MSCTI is designed to measure the electrical conductivity and temperature of solutions containing conductive ions. MSCTI is a lab instrument used to measure turbulent density and temperature variations in salt-stratified water flows, turbulent salinity flux and to determine density profiles.

  1. Why does my MSCTI have oscillations on it's outputs?

    There are two classes of oscillations as far as MSCTI goes. These are periodic variations that occur at the same frequency and phase as the AC...

    Started by Michael Head, 06-22-2011 10:55 PM
    • Replies: 0
    • Views: 19,137
    Michael Head
    06-22-2011 10:55 PM Go to last post

  2. What Does the Phase Error Light Indicate?

    The MSCTI box has three small red lights. One of these indicates that the power is on to the box, the next indicates that an internal voltage for...

    Started by Michael Head, 09-30-2010 06:46 PM
    • Replies: 0
    • Views: 1,956
    Michael Head
    09-30-2010 06:46 PM Go to last post

  3. What happens if the sensor is operated in air?

    Salt won't crystallize on the sensor if it is immersed so you are OK there. However, if the sensor is lifted into the air then crystallization can...

    Started by PMEAdmin, 09-15-2010 04:39 PM
    • Replies: 0
    • Views: 2,136
    PMEAdmin
    09-15-2010 04:39 PM Go to last post

  4. How many times do I have to repeat the T and C sensors calibration?

    MSCTI should hold about 1% accuracy for 8 hours. It will actually do better, more than 24 hours for 1%. However sub-1% errors are random and occur...

    Started by PMEAdmin, 09-15-2010 04:38 PM
    • Replies: 0
    • Views: 1,235
    PMEAdmin
    09-15-2010 04:38 PM Go to last post

  5. I would like to measure conductivity between rods or fibers in a liquid flow

    Time response for the MSCTI is very fast, roughly 800 Hz. This is limited by the electronics within the instrument. In most experiments, where fluid...

    Started by PMEAdmin, 09-15-2010 04:28 PM
    • Replies: 0
    • Views: 1,341
    PMEAdmin
    09-15-2010 04:28 PM Go to last post

  6. What is the maximum allowed length of cable between the sensor and the power supply?

    The MSCTI is shipped with a 10 meter cable between the sensor and box. One end of this cable is glued into the sensor electronics. The other has a...

    Started by PMEAdmin, 09-15-2010 04:27 PM
    • Replies: 0
    • Views: 1,446
    PMEAdmin
    09-15-2010 04:27 PM Go to last post

  7. What is the need to connect a MSCTI to a personal computer?

    The MSCTI produces two analog output voltages, one proportional to conductivity and one non-linearly proportional to temperature. These voltages...

    Started by PMEAdmin, 09-15-2010 04:26 PM
    • Replies: 0
    • Views: 1,462
    PMEAdmin
    09-15-2010 04:26 PM Go to last post
+ Post New Thread

Forum Information and Options

Moderators of this Forum

Thread Display Options

Use this control to limit the display of threads to those newer than the specified time frame.

Allows you to choose the data by which the thread list will be sorted.

Order threads in...

Note: when sorting by date, 'descending order' will show the newest results first.

Icon Legend

Contains unread posts
Contains unread posts
Contains no unread posts
Contains no unread posts
More than 15 replies or 150 views
Hot thread with unread posts
More than 15 replies or 150 views
Hot thread with no unread posts
Closed Thread
Thread is closed
Thread Contains a Message Written By You
You have posted in this thread

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts

Forum Rules